The R4 simulation to Cisco1941-SEC Cisco1941-SEC the frame relay switch, clock frequency, need to configure the interface encapsulation type, LMI type, the frame relay switch... The clock frequency, the configuration interface of s0/0 type, LMI type: R4 (config) #frame-relay switching is set to the frame relay switch R4 (config) #int s0/0 R4 (config-if) #no shut R4 (config-if) #clock rate 64000 R4 (config-if) #encapsulation frame-relay encapsulation frame relay R4 (config-if) #frame-relay lmi-type Cisco LMI type Cisco R4 (config-if) #frame-relay intf-type DCE configuration to a frame relay DCE end Other R4 configuration interface; Configure the frame relay switching table, each of the three interface configuration: R4 (config) #int s0/0 R4 (config-if) #frame-relay route 102 interface s0/1 201 R4 (config-if) #frame-relay route 104 interface s0/2 401 R4 (config) #int s0/1 R4 (config-if) #frame-relay route 201 interface s0/0 102 R4 (config-if) #frame-relay route 301 interface s0/2 103 R4 (config) #int s0/2 R4 (config-if) #frame-relay route 401 interface s0/0 104 R4 (config-if) #frame-relay route 103 interface s0/1 301 In the s0/0 interface to receive DLCI 102 frames, R4 will take it from the s0/1 sent to DLCI to 201, followed by analogy... To this, R4 has become a frame relay switch. Look at the R1 port configuration, add IP and encapsulation frame relay: R1 (config) #int s0/0 R1 (config-if) #encapsulation frame-relay R1 (config-if) #frame-relay lmi-type Cisco R1 (config-if) #ip add 192.168.1.1 255.255.255.0 R1 (config-if) #no Shu R1 (config-if) #exit R2, R3., in addition to a different address; R1#ping 192.168.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.1.1, timeout is 2 seconds: ..... Success rate is percent (0/5) 0 R1#ping 192.168.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.1.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 24/84/144 MS R1#ping 192.168.1.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.1.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 36/80/124 MS R1# R3#ping 192.168.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 20/61/136 MS R3#ping 192.168.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.1.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 32/89/160 MS R3# Cisco 1921-SEC Cisco 1921-SEC
blogpay
Total Comments: 0